Marine electronics

Accu Control:
Small and smart programmable system. Watching the accumulators. Can start and stop the generator on its own to charge the battery. Panel 12x12cm - 4.7x4.7 inch. Is also able to read pressure and temperature sensor.

Anemometer (only speed):
Measures Wind speed to 15 Beaufort. Maximum speed indication. With speed sensor. Panel 12x6cm (4.7x2.4inch) 12/24 volt.

Anemometer + Wind direction:
Wind speed up to 13 Beaufort(>160km/h), 16 Direction indicator. With speed + direction sensor. Panel 18x18cm (±7x7inch) 12 / 24 volt. + NMEA output Speed/Dir.

Bilges Alarm:
5 channels with pomp control, 12/24Vdc. Panel 6x12cm - 2.4x4.7 inch Programmable positive or negative input, relais and buzzer for each channel. Please also check our Motor Alarm.

Board Intercom: 4x20W intercom, 12 or 24 Vdc. Panel 12x12cm.

Board lights 8 lamps:
Complete panel to take care of the board lights. Switches, fuses, control all in one. Nothing has to be added to it, except the lamps. 12 / 24 Vdc, panel 12x12cm - 4.7x4.7 inch 8 lamps.

Board lights 11 lamps:
Complete panel to take care of the board lights. Switches, fuses, control all in one. Nothing has to be added to it, except the lamps. 12 / 24 Vdc, panel 12x16cm - 4.7x6.3 inch 11 lamps.

Bow propellor positionner:
Panel with indicator AND positionning button for the wheel house side and a axial position sensor (encoder) that rotate togehter with the bow thruster. Panel 16x12cm - 6.3x4.7 inch + encoder provided 60x80mm. (video)

Clinometer:

To see if the barge is charged horizontally. External indicators (7 lamps) can be directly connected. 24 Vdc, panel 16x12cm - 6.3x4.7 inch.

Controller SMS. Your board, voltage, temperature, bilges, alarm (door contact or else) anywhere on your mobile. But also a remote control to let you switch any thing from your mobile. So, a remote control and alarm in one! Complete system, ready to use, only a SIM card to add...

Double Tachometers LCD display: Count 2 rotation speeds from 48 to more than 10000 Rotation Per Minute. Two sensors are provided so that two different speeds can be mesured at the same time. ex: engine and propellor axe or two different engines.

Motor Alarm: Input accepts both Normally Closed or Normally Open sensors. 2 inputs for engine Temp + Pressure. 2 inputs for clutch Temp + Pressure. 1 extra input, relais output, programmable for each Channel. (6x12cm) 2.4x4.7in, 12/24 Vdc.

Power Meter "PM" All in one multi-function monitoring meter. Replace many kinds of meters (10x10x8cm). The mesured parameters are; Current (each phase or each group), phase voltage, line voltage, active, reactive, apparent power,

power factor and kWatt hour (can be synchronized to the existing one!).

The 3 phases instrument can be installed at power site (generators or high power grid up to 500A CT) and the mono phase can be installed at common power site like home, small workshop etc...

Remote control (UHF):
Special design for crane and generators (functions also work simultaneously).
Digital and encrypted. Power relais in recepteur box output for 12 and 24 Volt.

Rudder indicator: Analog, digital or graphic.

Servo Motor: Power H bridge 4Q 24V 125A. With Permanent Magnet motor.

Tachometer + Totalisator (NMEA): Small cylinder (14x2cm 0.9x5.5inch) waterproof (immersible) magnetic sensor. Serial output RS232TTL sypply 5 to 16Vdc via usb cable. 28 to13050RPM, programable NMEA format (video).

Tachometers single with red display:
Counts rotation speeds to 9999 Rotation Per Minutes. Complet delivery with sensor.

Thermocouple thermometer
Type D 0-1200° NMEA output or Display panel.

Water/Biges Alarm.
5 inputs. Just 5 wires as sensors (or any close or make)! Programmable low or high voltage input level. Memory (will remember alarm). Alarm buzzer and Pump relais output on panel.